The kids have gotten very excited about loft beds. I like the idea as
well: they make good use of space. Lily's room, in particular is
quite small, 7ft in the shortest dimension. A bed is just a bit
shorter than that, so it's a good candidate for a wall-to-wall loft:
Here it is in the room, with a ladder running up the wall:
It would be good to have a bed where even an adult can sit upright.
We measured me, and I need just under 36", though I also would sink
into a mattress a bit and rarely sit exactly upright. We're currently
thinking of doing 36" from the top of the mattress to the ceiling..
Since this is a wall-to-wall design, a simple way to do it is to
attach a 2x4 through the drywall into the studs, rest 3/4" plywood on
top, and put the mattress on that:
In an area with higher humidity I think you'd want to use bed slats or
drill holes in the plywood to help the mattress dissipate moisture,
but I don't think this is needed in New England (Julia and I have our
mattress on the floor).
This works for the three sides supported by walls, but the third side
runs across the room. Something similar to the other three sides
would work, except you lose headroom when going under the bed, which
is exacerbated by needing a thicker beam for the longer run. Instead,
I'm planning on using a 2x8 that's level with the mattress, and 6ft
of angle iron to support the plywood:
The 2x8 can be supported by the wall-mounted 2x4s, but it also needs something
to keep it from rotating. Here's how I'm thinking of using a few more
2x4 sections to support it:
I'm also planning to make a guard so she doesn't fall out, and attach
it to the 2x8. Probably three 2x4s: two vertical and one horizontal.
Construction screws, 1.5" (angle iron), 3" (attaching
2xs) and 3.5" (attaching to studs).
~$30
Paint and primer (Soft Turquoise)
$160
Total
It will actually be a bit cheaper because I already have some of the
things that I bought in bulk (fasteners, sandpaper, primer).
I normally wouldn't design quite so much in advance, and plan to
figure things out as it went up, but Lily wants it painted. It will
be easier to sand, prime, and paint everything in advance instead of
fully clearing that side of the room, though I'll probably need to do
a bit of touching up after.
This seems like it should be pretty good, though it's hard to say for
sure not having tried building it yet.
Looks cool! I remember being excited about these when I was a kid.
Could you share some details on how you make those drawings which aren't just cross-sections? I do some basic construction but I don't have any training in it and my drawing skills suck but I'm not sure where to start.
If having a name helps: the first one looks like isometric projection.
It's probably not very sensitive to getting the angles exact, if you don't need exact lengths either. But when I was taught to draw like that in school (some time between ages 11 and 14) we used paper with a dotted triangular grid, I think something like this, to get them without measuring.
3jefftk
One way what I'm doing here is a bit easier is that I'm not actually doing a perspective sketch. This is a parallel projection, where parallel lines in reality remain parallel in the drawing. That means it doesn't look exactly like anything you might actually see, but it's close and much easier to draw.
The style of the second drawing is a bit easier than the first. You start by sketching everything that's in one plane, with vertical lines vertical and horizontal lines that are perpendicular to you horizontal. To make things the right size you can use a ruler and pick some a scale: 1 inch to the foot or something. Then when you need to draw a horizontal lines that are "coming out of the page" instead make them at an angle. Exactly which angle you choose doesn't matter that much, but once you've picked that angle you should make sure anything else parallel uses exactly the same angle.
I haven't taken a class, but this also isn't something I was born able to do. Just lots of doing it until I have results I like.
The kids have gotten very excited about loft beds. I like the idea as well: they make good use of space. Lily's room, in particular is quite small, 7ft in the shortest dimension. A bed is just a bit shorter than that, so it's a good candidate for a wall-to-wall loft:
Here it is in the room, with a ladder running up the wall:
It would be good to have a bed where even an adult can sit upright. We measured me, and I need just under 36", though I also would sink into a mattress a bit and rarely sit exactly upright. We're currently thinking of doing 36" from the top of the mattress to the ceiling..
Since this is a wall-to-wall design, a simple way to do it is to attach a 2x4 through the drywall into the studs, rest 3/4" plywood on top, and put the mattress on that:
In an area with higher humidity I think you'd want to use bed slats or drill holes in the plywood to help the mattress dissipate moisture, but I don't think this is needed in New England (Julia and I have our mattress on the floor).
This works for the three sides supported by walls, but the third side runs across the room. Something similar to the other three sides would work, except you lose headroom when going under the bed, which is exacerbated by needing a thicker beam for the longer run. Instead, I'm planning on using a 2x8 that's level with the mattress, and 6ft of angle iron to support the plywood:
The 2x8 can be supported by the wall-mounted 2x4s, but it also needs something to keep it from rotating. Here's how I'm thinking of using a few more 2x4 sections to support it:
I'm also planning to make a guard so she doesn't fall out, and attach it to the 2x8. Probably three 2x4s: two vertical and one horizontal.
Materials:
It will actually be a bit cheaper because I already have some of the things that I bought in bulk (fasteners, sandpaper, primer).
I normally wouldn't design quite so much in advance, and plan to figure things out as it went up, but Lily wants it painted. It will be easier to sand, prime, and paint everything in advance instead of fully clearing that side of the room, though I'll probably need to do a bit of touching up after.
This seems like it should be pretty good, though it's hard to say for sure not having tried building it yet.
Comment via: facebook